ASTM A370 - 17a
Standard Test Methods and Definitions for Mechanical Testing of Steel Products
| Aviso: | Las normas ASTM en lectura se visualizan a través del área decliente. Los archivos no se pueden descargar | ||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Fecha edición: |
2017-11-15
Anulada
|
||||||||||||||||||||||||||||||||||||||||
| Fecha cancelación: | 2017-11-15 | ||||||||||||||||||||||||||||||||||||||||
| Idiomas disponibles: | Inglés | ||||||||||||||||||||||||||||||||||||||||
| Resumen: | |||||||||||||||||||||||||||||||||||||||||
| Keywords: | bend test; Brinell hardness; Charpy impact test; elongation; FATT (Fracture Appearance Transition Temperature); hardness test; Izod impact test; portable hardness; reduction of area; Rockwell hardness; tensile strength; tension test; yield strength; | ||||||||||||||||||||||||||||||||||||||||
| Scope: | 1.1 These test methods2 cover procedures and definitions for the mechanical testing of steels, stainless steels, and related alloys. The various mechanical tests herein described are used to determine properties required in the product specifications. Variations in testing methods are to be avoided, and standard methods of testing are to be followed to obtain reproducible and comparable results. In those cases in which the testing requirements for certain products are unique or at variance with these general procedures, the product specification testing requirements shall control. 1.2 The following mechanical tests are described:
1.3 Annexes covering details peculiar to certain products are appended to these test methods as follows:
1.4 The values stated in inch-pound units are to be regarded as the standard. 1.5 When this document is referenced in a metric product specification, the yield and tensile values may be determined in inch-pound (ksi) units then converted into SI (MPa) units. The elongation determined in inch-pound gauge lengths of 2 or 8 in. may be reported in SI unit gauge lengths of 50 or 200 mm, respectively, as applicable. Conversely, when this document is referenced in an inch-pound product specification, the yield and tensile values may be determined in SI units then converted into inch-pound units. The elongation determined in SI unit gauge lengths of 50 or 200 mm may be reported in inch-pound gauge lengths of 2 or 8 in., respectively, as applicable. 1.5.1 The specimen used to determine the original units must conform to the applicable tolerances of the original unit system given in the dimension table not that of the converted tolerance dimensions. Note 1: This is due to the specimen SI dimensions and tolerances being hard conversions when this is not a dual standard. The user is directed to Test Methods A1058 if the tests are required in SI units. 1.6 Attention is directed to ISO/IEC 17025 when there may be a need for information on criteria for evaluation of testing laboratories. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||||||||||||||||||||||
| ICS: | 77.040.10 - Ensayos mecánicos de metales, 77.140.01 - Productos de fundición y productos de acero en general | ||||||||||||||||||||||||||||||||||||||||
| CTN: | A01.13 - A01.13 | ||||||||||||||||||||||||||||||||||||||||
|
Otras Relaciones |
Es referenciada por A0049-12R19 Es referenciada por A0618_A0618M-21 Es referenciada por A1057_A1057M-08R19 Es referenciada por A0131_A0131M-19 Es referenciada por A1082_A1082M-16R21 Es referenciada por A0356_A0356M-21 Es referenciada por G0129-21 Es referenciada por A0020_A0020M-20 Es referenciada por A0985_A0985M-21 Es referenciada por A1001-18 Es referenciada por A1110_A1110M-21 Es referenciada por A0726-18 Es referenciada por A0066-21 Es referenciada por A1113_A1113M-20E01 Es referenciada por A0805_A0805M-09R21 Es referenciada por A0264-12R19 Es referenciada por A1024_A1024M-18 Es referenciada por A0974-97R21 Es referenciada por A0764-07R21 Es referenciada por A0955_A0955M-20C |
Normas citadas
Libros relacionados
Normas relacionadas
Colecciones temáticas relacionadas
