ASTM A27/A27M - 20
Standard Specification for Steel Castings, Carbon, for General Application
| Aviso: | Las normas ASTM en lectura se visualizan a través del área decliente. Los archivos no se pueden descargar |
|---|---|
| Fecha edición: |
2020-05-01
En Vigor
|
| Idiomas disponibles: | Inglés |
| Resumen: | This specification covers carbon steel castings for general applications. The grades of steels covered here are: Grade N-1, Grade N-2, Grade U-60-30 [415-205], Grade 60-30 [415-205], Grade 65-35 [450-240], Grade 70-36 [485-250] and Grade 70-40 [485-275]. Except for Grades N-1 and U-60-30, all steel castings shall be heat-treated by full annealing, normalizing, normalizing and tempering, or quenching and tempering. Heat treatments shall be performed after castings have been allowed to cool. Heat and product analyses shall be performed wherein specimens shall conform to required chemical composition of carbon, manganese, silicon, sulfur and phosphorus. Except for Grades N-1 and N-2, all steels shall undergo tension test, and shall conform to the following mechanical requirements: tensile strength, yield point, elongation, and reduction of area. |
| Keywords: | castings; general application; steel; |
| Scope: | 1.1 This specification covers carbon steel castings for general applications that require up to 70 ksi (485 MPa) minimum tensile strength. Note 1: The grades covered by this specification represent materials that are suitable for assembly with other steel castings or wrought steel parts by fusion welding. It is not intended to imply that all these grades possess the same degree of weldability or that the same welding techniques can be used on all castings. It is the responsibility of the purchaser to establish for himself a suitable welding technique. 1.2 Several grades and two classes of steel castings are covered, as indicated below. The grade and class desired shall be specified by the purchaser. 1.2.1 Grade N-1—Chemical analysis only. 1.2.2 Grade N-2—Heat treated but not mechanically tested. 1.2.3 Grade U-60-30 [415-205]—Mechanically tested but not heat treated. 1.2.4 Grades 60-30 [415-205], 65-35 [450-240], 70-36 [485-250], and 70-40 [485-275]—Heat treated and mechanically tested. 1.2.5 Class 1 and Class 2 steel castings shall be specified in accordance with 9.2. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| ICS: | 77.140.80 - Fundición y acero moldeado |
| CTN: | A01.18 - A01.18 |
|
Anulaciones Normas |
Anula a A0027_A0027M-19 |
|
Otras Relaciones |
Es referenciada por C1572/C1572M - 23 Es referenciada por F1510-21 Es referenciada por A0957_A0957M-21 Es referenciada por A0781_A0781M-21 Es referenciada por A0036_A0036M-19 Es referenciada por F2936-23 Es referenciada por F2798-09R23 Es referenciada por C0361M-22 Es referenciada por F2935-23 Es referenciada por C0361-22 Es referenciada por A148/A148M - 24 Es referenciada por A488/A488M - 24 Es referenciada por F765 - 25 Es referenciada por F1106 - 87(2023) |
Normas citadas
Libros relacionados
Normas relacionadas
Colecciones temáticas relacionadas
