AENOR Logo

Normas SAE

49607 Resultados disponibles

Filtrar:

(40721)
(8886)
SAE

SAE AMS4908E
En Vigor
1993-05-01
TITANIUM ALLOY SHEET AND STRIP 8Mn Annealed, 110,000 psi (760 MPa) Yield Strength
 
SAE

SAE AMS2759/1E
En Vigor
2014-04-23
Heat Treatement of Carbon and Low-Alloy Steel Parts Minimum Tensile Strength Below 220 ksi (1517 MPa)
 
SAE

SAE AMS3021D
En Vigor
2007-01-09
Fluid, Reference for Testing Di-Ester (Polyol) Resistant Material
 
SAE

SAE AMS3281A
En Vigor
1996-11-01
SEALING COMPOUND, POLYSULFIDE (T) SYNTHETIC RUBBER for Integral Fuel Tank and Fuel Cell Cavities Low Density (1.20 to 1.35 sp gr), for Intermittent Use to 360 °F (182 °C)
 
SAE

SAE AMS3658B
En Vigor
2011-08-09
POLYTETRAFLUOROETHYLENE EXTRUSIONS Premium Strength, Stress-Relieved, Radiographically Inspected
 
SAE

SAE AMS4297B
En Vigor
2018-07-25
Aluminum Alloy Sheet 4.4Cu - 1.5Mg - 0.60Mn (2024; -T4 Flat Sheet) Solution Heat Treated, High Formability
 
SAE

SAE AMS4610L
En Vigor
1989-07-01
BRASS BARS AND RODS, FREE-CUTTING 61.5Cu - 3.1Pb - 35Zn Half Hard (H02)
 
SAE

SAE AMS4186C
En Vigor
2004-11-17
Aluminum Alloy Bars, Rods, and Wire, Rolled or Cold Finished 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7075-F) As Fabricated
 
SAE

SAE AMS2451/3B
En Vigor
2016-11-29
Plating, Brush, Nickel Low Stress, Low-Hardness Deposit
 
SAE

SAE AMS4893D
En Vigor
2022-05-12
Alloy Castings, Corrosion- and Heat-Resistant 66Ni - 29Cu - 4.0Si Solution Treated
 
SAE

SAE AIR1069B
En Vigor
2015-06-02
Crew Oxygen Requirements Up to a Maximum Altitude of 45,000 Ft.
 
SAE

SAE AMS4239A
En Vigor
1984-07-01
ALUMINUM ALLOY CASTINGS, SAND 6.8Mg - 0.18Ti - 0.18Mn (535.0-0) Annealed
 
SAE

SAE AMS4218E
En Vigor
1990-07-01
ALUMINUM ALLOY CASTINGS 7.0Si - 0.35Mg (A356.0-T61P) Solution and Precipitation Heat Treated
 
SAE

SAE AMS4150N
En Vigor
2019-05-14
Aluminum Alloy, Extrusions and Rings 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr - (6061-T6) Solution and Precipitation Heat Treated
 
SAE

SAE AMS3571/9C
En Vigor
2011-09-23
Resin, Polyether Urethane (EU) Casting Flexible, Solid, Unfilled 75 Durometer “D”
 
SAE

SAE AIR1873
En Vigor
2012-03-28
Guide to Limited Engine Monitoring Systems for Aircraft Gas Turbine Engines
 
SAE

SAE AMS4217D
En Vigor
1959-06-15
ALUMINUM ALLOY CASTINGS, SAND 7Si - 0.3Mg (356-T6)
 
SAE

SAE AMS4505C
En Vigor
1949-02-01
BRASS SHEET AND STRIP 70Cu - 30Zn Annealed
 
SAE

SAE AMS4590B
En Vigor
2006-04-24
Extrusions, Nickel-Aluminum Bronze, Martensitic 78.5Cu - 10.5Al - 5.1Ni - 4.8Fe Solution Heat Treated and Tempered (TQ50)
 
SAE

SAE AMS3175A
En Vigor
2011-04-19
Non-Chromated Surface Pretreatment Prior to Painting
 
SAE

SAE AMS4001H
En Vigor
2002-08-21
Aluminum Sheet and Plate 0.12Cu (1100-0) Annealed
 
SAE

SAE AMS2447C
En Vigor
2006-09-22
Coating, Thermal Spray High Velocity Oxygen/Fuel Process
 
SAE

SAE AIR5683
En Vigor
2011-11-15
High Performance 1553 Research and Development
 
SAE

SAE AGS887-5
En Vigor
1945-04-11
AGS887 3/8" B.F.S. Studs
 
SAE

SAE AMS3909/3A
En Vigor
2022-10-04
Cloth, Aramid 2.0 oz per sq yd (68 g/m2), 230 Pounds Force per Inch (40279 N/m) (Warp) and 220 Pounds Force per Inch (38528 N/m) (Filling)
 
SAE

SAE AMS4227C
En Vigor
1988-04-01
ALUMINUM ALLOY CASTINGS, SAND 8.0Cu - 6.0Mg - 0.50Mn - 0.50Ni (A240.0-F) As Cast
 
SAE

SAE AGS2081-11
En Vigor
2000-03-01
AGS2081 Pipe Clip for 3/16" DIA. Fixing, Rubber Covered, with Earthing Tongue
 
SAE

SAE AIR5273
En Vigor
2007-01-11
Actuation System Failure Detection Methods
 
SAE

SAE AMS3218B
En Vigor
2001-05-01
Fluorocarbon (FKM) Rubber High-Temperature-Fluid Resistant Low Compression Set 85 to 95
 
SAE

SAE AMS3050/9A
En Vigor
2024-12-04
Performance Specification Anti-Seize Thread Compound, High Temperature - ‘Graphite+Calcium Fluoride’ Only
 
SAE

SAE AMS4079C
En Vigor
1979-01-01
ALUMINUM ALLOY TUBING, SEAMLESS, DRAWN, ROUND, CLOSE TOLERANCE 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061-0)
 
SAE

SAE AMS4252B
En Vigor
2012-04-02
Aluminum Alloy, Plate 6.4Zn - 2.4Mg - 2.2Cu - 0.12Zr (7150-T7751) Solution Heat Treated, Stress Relieved, and Overaged
 
SAE

SAE AMS3198H
En Vigor
1973-12-01
SPONGE, CHLOROPRENE-RUBBER Medium
 
SAE

SAE AMS3221A
En Vigor
1944-03-01
SYNTHETIC RUBBER Repid Fuel Swelling (45-55)
 
SAE

SAE AMS4231G
En Vigor
2005-02-11
Castings, Sand, 4.5Cu - 1.1Si, Solution and Precipitation Heat Treated
 
SAE

SAE AMS4029K
En Vigor
2006-05-16
Aluminum Alloy Sheet and Plate (2014; -T6 Sheet, -T651 Plate) Solution and Precipitation Heat Treated
 
SAE

SAE AMS2643D
En Vigor
2007-05-30
Structural Examination of Titanium Alloys Chemical Etch Inspection Procedure
 
SAE

SAE AMS5384C
En Vigor
1985-04-01
ALLOY CASTINGS, INVESTMENT, CORROSION AND HEAT RESISTANT 53Ni - 18Cr - 18Co - 4.0Mo - 2.9Ti - 2.9Al - 0.006B Vacuum-Melted, Vacuum-Cast, Solution and Precipitation Heat Treated
 
SAE

SAE AGS1216-10
En Vigor
1975-03-01
AGS1216 Standard Union Nuts (Steel)
 
SAE

SAE AMS4212M
En Vigor
2025-12-01
Aluminum Alloy Castings, 5.0Si - 1.2Cu - 0.50Mg (355.0-T6), Solution and Precipitation Heat Treated
 
SAE

SAE AIR1839D
En Vigor
2017-01-04
A Guide to Aircraft Turbine Engine Vibration Monitoring Systems
 
SAE

SAE AIR1380A
En Vigor
1997-01-01
RECOMMENDED PRACTICE FOR MEASUREMENT OF STATIC MECHANICAL STIFFNESS PROPERTIES OF AIRCRAFT TIRES
 
SAE

SAE AMS4966D
En Vigor
1972-11-15
TITANIUM ALLOY FORGINGS 5Al - 2.5Sn Annealed, 110,000 psi (758 MPa) Yield Strength
 
SAE

SAE AMS4771C
En Vigor
1974-06-01
BRAZING FILLER METAL, SILVER 50Ag - 16Cd - 15.5Zn - 15.5Cu - 3.0Ni 1170°- 1270°F (632°- 688°C) Melting Range
 
SAE

SAE AMS2368A
En Vigor
2002-11-22
Sampling and Testing of Wrought Titanium Raw Material Except Forgings and Forging Stock
 
SAE

SAE AMS4094D
En Vigor
2018-03-23
Aluminum Alloy, Sheet and Plate, Alclad 6.3Cu - 0.30Mn - 0.18Zr - 0.10V - 0.06Ti Alclad 2219-T81 Sheet Solution Heat Treated, Cold Worked, and Precipitation Heat Treated Alclad 2219-T851 Plate Solution Heat Treated, Stress Relieved, and Precipitation Heat Treated
 
SAE

SAE AGS1582-7
En Vigor
1939-02-05
AGS1582 B.A Washers
 
SAE

SAE AMS3568/1B
En Vigor
2011-08-25
Foam, Polyether Urethane (EU) Elastomer, Shock Absorbing 5 Pounds/Cubic Foot (80 kg/m3) Density
 
SAE

SAE AGS2085-5
En Vigor
1970-05-22
AGS2085 Special Pipe Couplings (Aluminium Alloy) Outer Sleeve
 
SAE

SAE AMS3272
En Vigor
2011-08-25
CLOTH, NYLON, POLYURETHANE COATED Thermally, Radio Frequency, or Ultrasonically Sealable
 
SAE

SAE AMS4924H
En Vigor
2015-08-06
Titanium Alloy Bars, Forgings, and Rings-15 5Al - 2.5Sn, Extra Low Interstitial Annealed
 
SAE

SAE AMS2212A
En Vigor
1950-06-15
TOLERANCES Magnesium Alloy Sheet and Plate
 
SAE

SAE AMS5115A
En Vigor
1943-10-01
CARBON STEEL SPRING WIRE Valve Spring Quality
 
SAE

SAE AIR4092
En Vigor
2011-08-10
INVESTIGATION OF PTFE "MELT" PHENOMENON FOR HIGH PRESSURE HOSES
 
SAE

SAE AMS4901L
En Vigor
1986-07-01
TITANIUM SHEET, STRIP, AND PLATE Annealed, 70,000 psi (485 MPa) Yield Strength
 
SAE

SAE AIR1375A
En Vigor
1988-06-01
MINIMUM SAFETY REQUIREMENTS FOR SPECIAL PURPOSE AIRLINE GROUND SUPPORT EQUIPMENT
 
SAE

SAE AMS1550B
En Vigor
2012-02-23
Cleaner, Water Base, Aircraft interior Hard Surface Materials
 
SAE

SAE AMS2645B
En Vigor
1953-06-15
FLUORESCENT PENETRANT INSPECTION
 
SAE

SAE AMS4190F
En Vigor
1996-07-01
ALUMINUM ALLOY WELDING WIRE 5.2Si (4043)
 
SAE

SAE AMS3814/13
En Vigor
1993-10-01
CORD, CORELESS, PARA-ARAMID Intermediate Modulus 250 lb (1110 N), 1800 ft per lb (1210 m/kg)