AENOR Logo

Normas SAE

49877 Resultados disponibles

Filtrar:

(40986)
(8891)
SAE

SAE AMS2516E
En Vigor
2013-03-21
Polytetrafluoroethylene (PTFE) Resin Coating High Build, 698 to 752 °F (370 to 400 °C) Fusion
SAE

SAE AMS3622D
En Vigor
1996-10-01
Plastic Moldings and Extrusions Cellulose Acetate, General Purpose
SAE

SAE AMS2269G
En Vigor
2022-09-14
Chemical Check Analysis Limits Nickel, Nickel Alloys, and Cobalt Alloys
SAE

SAE AMS3228C
En Vigor
1951-03-01
SYNTHETIC RUBBER Hot Oil and Coolant Resistant (65-75)
SAE

SAE AMS3349A
En Vigor
1977-01-01
SILICONE RUBBER 1100 psi (7.58 MPa) Tensile Strength, High Resiliency 65 - 75
SAE

SAE AMS2482F
En Vigor
2022-07-08
Hard Anodic Coating on Aluminum Alloys Polytetrafluoroethylene (PTFE)-Impregnated or Codeposited
SAE

SAE AMS2221E
En Vigor
1988-04-01
TOLERANCES Copper and Copper Alloy Bars and Rods
SAE

SAE AMS3249C
En Vigor
1998-08-01
Ethylene Propylene (EPDM) Rubber Hydrazine-Base-Fluid Resistant 75 - 85
SAE

SAE AMS1631C
En Vigor
2005-07-22
Cleaner, Carpet Water Extraction Type
SAE

SAE AMS3710B
En Vigor
2011-08-09
SANDWICH STRUCTURES, GLASS FABRIC-RESIN Low Pressure Molded, Heat Resistant
SAE

SAE AMS2980B
En Vigor
2021-09-23
Carbon Fiber Fabric and Epoxy Resin Wet Lay-Up Repair Material Part 0 - Introduction
SAE

SAE AMS2373B
En Vigor
1998-07-01
Quality Assurance Sampling of Bolts and Screws
SAE

SAE AMS3654B
En Vigor
2011-08-09
TUBING, ELECTRICAL INSULATION Light Wall, Extruded Polytetrafluoroethylene (PTFE)
SAE

SAE AMS4456A
En Vigor
2019-11-25
Aluminum Alloy, Hand Forgings 8.0Zn - 1.0Cu - 1.6Mg - 0.12Zr (7037-T7452) Solution Heat Treated, Compression Stress Relieved, and Overaged
SAE

SAE AMS3325F
En Vigor
2014-05-28
Fluorosilicone (FVMQ) Rubber Fuel and Oil Resistant 55 – 65
SAE

SAE AMS3678/8
En Vigor
2006-06-20
Type 8 Virgin Polytetrafluoroethylene (PTFE) Moldings or Extrusions with 10% Carbon Fiber
SAE

SAE AMS4901D
En Vigor
1968-11-01
TITANIUM SHEET, STRIP, AND PLATE Annealed, 70,000 psi Yield
SAE

SAE AMS3208F
En Vigor
1965-02-01
SYNTHETIC RUBBER Weather Resistant, Chloroprene Type 45 - 55
SAE

SAE AMS5342E
En Vigor
2014-04-09
Steel, Corrosion-Resistant, Investment Castings 16Cr - 4.1Ni - 0.28Cb (Nb) - 3.2Cu Homogenization, Solution, and Precipitation Heat Treated (H1100) 130 ksi (896 MPa) Tensile Strength (17-4)
SAE

SAE AMS4261G
En Vigor
2017-03-30
Aluminum Alloy Castings, Investment 7.0Si - 0.32Mg (356.0-T51) Precipitation Heat Treated