Estamos mejorando nuestra Tienda, Portal de clientes y Aenormas para ofrecerte una mejor experiencia.
Si detectas cualquier incidencia o necesitas ayuda durante el proceso de compra, puedes contactarnos a través del chat o escribirnos a normas@aenor.com.
Nuestro equipo estará encantado de ayudarte.
ASTM D92 - 24
Standard Test Method for Flash and Fire Points by Cleveland Open Cup Tester
| Fecha edición: |
2024-11-01
En Vigor
|
|---|---|
| Idiomas disponibles: | Inglés |
| Resumen: | |
| Keywords: | automated Cleveland open cup; Cleveland open cup; fire point open cup for flash point; flammability; flash point; petroleum products; |
| Scope: | 1.1 This test method describes the determination of the flash point and fire point of petroleum products by a manual Cleveland open cup apparatus or an automated Cleveland open cup apparatus. Note 1: The precisions for fire point were not determined in the current interlaboratory program. Fire point is a parameter that is not commonly specified, although in some cases, knowledge of this flammability temperature may be desired. 1.2 This test method is applicable to all petroleum products with flash points above 79 °C (175 °F) and below 400 °C (752 °F) except fuel oils. Note 2: This test method may occasionally be specified for the determination of the fire point of a fuel oil. For the determination of the flash points of fuel oils, use Test Method D93. Test Method D93 should also be used when it is desired to determine the possible presence of small but significant concentrations of lower flash point substances that may escape detection by Test Method D92. Test Method D1310 can be employed if the flash point is known to be below 79 °C (175 °F). 1.3 Units—The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.4 WARNING—Mercury has been designated by many regulatory agencies as a hazardous substance that can cause serious medical issues. Mercury, or its vapor, has been demonstrated to be hazardous to health and corrosive to materials. Use Caution when handling mercury and mercury-containing products. See the applicable product Safety Data Sheet (SDS) for additional information. The potential exists that selling mercury or mercury-containing products, or both, is prohibited by local or national law. Users must determine legality of sales in their location. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see 6.4, 7.1, 11.1.3, and 11.2.4. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| ICS: | 75.080 - Productos petrolíferos en general, 13.220.40 - Comportamiento frente al fuego e inflamabilidad de materiales y productos |
| CTN: | D02.08 - D02.08 |
|
Otras Relaciones |
Es referenciada por C0457_C0457M-24 Es referenciada por D0471-16AR21 Es referenciada por D2225-20 Es referenciada por D0117-22 Es referenciada por F2601 - 25 Es referenciada por D946/D946M - 25 Es referenciada por C990/C990M - 25 Es referenciada por D8584 - 24 Es referenciada por D4552/D4552M - 20(2025) Es referenciada por D8254-19 Es referenciada por D2878-21 Es referenciada por A0849-15R21 Es referenciada por D8240-22E01 Es referenciada por D4730-13R20 Es referenciada por D7942-15R23 Es referenciada por D3487 - 25 Es referenciada por D6361/D6361M - 98(2025) Es referenciada por D5372 - 25 Es referenciada por C647 - 19(2025) Es referenciada por F2161-21 |










