Estamos mejorando nuestra Tienda, Portal de clientes y Aenormas para ofrecerte una mejor experiencia.
Si detectas cualquier incidencia o necesitas ayuda durante el proceso de compra, puedes contactarnos a través del chat o escribirnos a normas@aenor.com.
Nuestro equipo estará encantado de ayudarte.
ASTM D3654/D3654M - 06(2024)
Standard Test Methods for Shear Adhesion of Pressure-Sensitive Tapes
| Fecha edición: |
2024-10-01
En Vigor
|
|---|---|
| Idiomas disponibles: | Inglés |
| Resumen: | |
| Keywords: | filament-reinforced tape; pressure-sensitive tape; shear adhesion; |
| Scope: | 1.1 This test method covers procedures for determining the ability of pressure-sensitive tapes and labels to remain adhered under constant load applied parallel to the surface of the tape and substrate. 1.1.1 Procedure A measures the shear adhesion when applied to a vertical standard steel panel. 1.1.2 Procedure B measures the shear adhesion when applied to vertical panel covered with NIST SRM 1810A standard fiberboard. 1.1.3 Procedure C measures the shear adhesion when applied to a vertical panel covered with a fiberboard as defined by Comite Europeen de Normalisation (CEN). 1.1.4 Procedure D measures shear adhesion when applied to a vertical panel covered with a fiberboard agreed upon by the buyer and seller. 1.1.5 Procedure E measures shear adhesion of filament reinforced tape when applied to a horizontal standard steel panel. 1.1.6 Procedure F measures shear adhesion of a filament reinforced tape when applied to a horizontal panel covered with NIST SRM 1810A standard fiberboard. 1.1.7 Procedure G measures the shear adhesion of a filament reinforced tape when applied to a horizontal panel covered with a standard fiberboard defined by CEN. 1.1.8 Procedure H measures the shear adhesion the same as Procedure A except the test is conducted at an elevated temperature and after a 10-min dwell time at the elevated temperature. 1.2 These procedures provide a means of assessing the uniformity of the adhesive of a given type of pressure-sensitive tape, usually tapes used for packaging applications. The assessment may be within a roll of tape, between rolls or production lots. 1.2.1 Variations in the tape backing and adhesive affect the response; therefore, these procedures cannot be used to pinpoint the specific cause(s) of nonuniformity. 1.2.2 This test method is intended to replace AFERA 4012, CEN 1943, and PSTC (see 7.2). 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems will result in non-conformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| ICS: | 55.040 - Material de embalaje y sus accesorios |
| CTN: | D10.14 - D10.14 |
|
Anulaciones Normas |
Anula a D3654_D3654M-06R19 |
|
Otras Relaciones |
Es referenciada por D1974_D1974M-22 Es referenciada por D5330_D5330M-06R20 Es referenciada por D6463_D6463M-06R20 Es referenciada por D5486_D5486M-06R20 |










