Estamos mejorando nuestra Tienda, Portal de clientes y Aenormas para ofrecerte una mejor experiencia.
Si detectas cualquier incidencia o necesitas ayuda durante el proceso de compra, puedes contactarnos a través del chat o escribirnos a normas@aenor.com.
Nuestro equipo estará encantado de ayudarte.
ASTM D2699 - 24b
Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
| Fecha edición: |
2024-12-01
Anulada
|
|---|---|
| Fecha cancelación: | 2024-12-01 |
| Idiomas disponibles: | Inglés |
| Resumen: | |
| Keywords: | guide table; |
| Scope: | 1.1 This laboratory test method covers the quantitative determination of the knock rating of liquid spark-ignition engine fuel in terms of Research O.N., including fuels that contain up to 25 % v/v of ethanol. However, this test method may not be applicable to fuel and fuel components that are primarily oxygenates.2 The sample fuel is tested using a standardized single cylinder, four-stroke cycle, variable compression ratio, carbureted, CFR engine run in accordance with a defined set of operating conditions. The O.N. scale is defined by the volumetric composition of PRF blends. The sample fuel knock intensity is compared to that of one or more PRF blends. The O.N. of the PRF blend that matches the K.I. of the sample fuel establishes the Research O.N. 1.2 The O.N. scale covers the range from 0 to 120 octane number but this test method has a working range from 40 to 120 Research O.N. Typical commercial fuels produced for spark-ignition engines rate in the 88 to 101 Research O.N. range. Testing of gasoline blend stocks or other process stream materials can produce ratings at various levels throughout the Research O.N. range. 1.3 The values of operating conditions are stated in SI units and are considered standard. The values in parentheses are the historical inch-pound units. The standardized CFR engine measurements continue to be in inch-pound units only because of the extensive and expensive tooling that has been created for this equipment. 1.4 For purposes of determining conformance with all specified limits in this standard, an observed value or a calculated value shall be rounded “to the nearest unit” in the last right-hand digit used in expressing the specified limit, in accordance with the rounding method of Practice E29. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see Section 8, 14.4.1, 15.5.1, 16.6.1, Annex A1, A2.2.3.1, A2.2.3.3 (6) and (9), A2.3.5, X3.3.7, X4.2.3.1, X4.3.4.1, X4.3.9.3, X4.3.11.4, and X4.5.1.8. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| ICS: | 75.160.20 - Combustibles líquidos |
| CTN: | D02.01 - D02.01 |
|
Otras Relaciones |
Es referenciada por D7320 - 18e1 Es referenciada por D2885 - 21(2025) Es referenciada por D8076 - 24 Es referenciada por D1310 - 14(2021) Es referenciada por D6617 - 21 Es referenciada por D8111 - 25 Es referenciada por D8275 - 22 Es referenciada por D4814 - 25 Es referenciada por D6227 - 24a Es referenciada por D7577 - 12(2021) Es referenciada por D8291 - 25 Es referenciada por D1094 - 24 Es referenciada por D8631 - 25 Es referenciada por D8340 - 22 Es referenciada por D471 - 16a(2021) Es referenciada por D6122 - 25 Es referenciada por D2700 - 25 Es referenciada por D6709 - 25 Es referenciada por D8321 - 25 Es referenciada por D6593 - 18e1 |










