Estamos mejorando nuestra Tienda, Portal de clientes y Aenormas para ofrecerte una mejor experiencia.
Si detectas cualquier incidencia o necesitas ayuda durante el proceso de compra, puedes contactarnos a través del chat o escribirnos a normas@aenor.com.
Nuestro equipo estará encantado de ayudarte.
ASTM A370 - 21
Standard Test Methods and Definitions for Mechanical Testing of Steel Products
| Fecha edición: |
2021-11-01
Anulada
|
||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Fecha cancelación: | 2021-11-01 | ||||||||||||||||||||||||||||||||||||||||
| Idiomas disponibles: | Inglés | ||||||||||||||||||||||||||||||||||||||||
| Resumen: | |||||||||||||||||||||||||||||||||||||||||
| Keywords: | bend test; Brinell hardness; Charpy impact test; elongation; FATT (Fracture Appearance Transition Temperature); hardness test; Izod impact test; portable hardness; reduction of area; Rockwell hardness; tensile strength; tension test; yield strength; | ||||||||||||||||||||||||||||||||||||||||
| Scope: | 1.1 These test methods2 cover procedures and definitions for the mechanical testing of steels, stainless steels, and related alloys. The various mechanical tests herein described are used to determine properties required in the product specifications. Variations in testing methods are to be avoided, and standard methods of testing are to be followed to obtain reproducible and comparable results. In those cases in which the testing requirements for certain products are unique or at variance with these general procedures, the product specification testing requirements shall control. 1.2 The following mechanical tests are described:
1.3 Annexes covering details peculiar to certain products are appended to these test methods as follows:
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 When these test methods are referenced in a metric product specification, the yield and tensile values may be determined in inch-pound (ksi) units then converted into SI (MPa) units. The elongation determined in inch-pound gauge lengths of 2 or 8 in. may be reported in SI unit gauge lengths of 50 or 200 mm, respectively, as applicable. Conversely, when these test methods are referenced in an inch-pound product specification, the yield and tensile values may be determined in SI units then converted into inch-pound units. The elongation determined in SI unit gauge lengths of 50 or 200 mm may be reported in inch-pound gauge lengths of 2 or 8 in., respectively, as applicable. 1.5.1 The specimen used to determine the original units must conform to the applicable tolerances of the original unit system given in the dimension table not that of the converted tolerance dimensions. Note 1: This is due to the specimen SI dimensions and tolerances being hard conversions when this is not a dual standard. The user is directed to Test Methods A1058 if the tests are required in SI units. 1.6 Attention is directed to ISO/IEC 17025 when there may be a need for information on criteria for evaluation of testing laboratories. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||||||||||||||||||||||
| ICS: | 77.140.01 - Productos de fundición y productos de acero en general, 77.040.10 - Ensayos mecánicos de metales | ||||||||||||||||||||||||||||||||||||||||
| CTN: | A01.13 - A01.13 | ||||||||||||||||||||||||||||||||||||||||
|
Otras Relaciones |
Es referenciada por A0564_A0564M-19A Es referenciada por A0530_A0530M-18 Es referenciada por E0606_E0606M-21 Es referenciada por A0551_A0551M-08R23 Es referenciada por C0692-13R23 Es referenciada por A1123_A1123M-22 Es referenciada por A0769_A0769M-17R23 Es referenciada por A1079-17R23 Es referenciada por A970/A970M - 25 Es referenciada por A240/A240M - 25a Es referenciada por A1064/A1064M - 24 Es referenciada por A536 - 24 Es referenciada por A865/A865M - 23 Es referenciada por A778/A778M - 24a Es referenciada por A53/A53M - 24 Es referenciada por A1008/A1008M - 24 Es referenciada por A787/A787M - 24 Es referenciada por A961/A961M - 25a Es referenciada por A875/A875M - 23 Es referenciada por A0955_A0955M-20C |
Normas citadas
Libros relacionados
Normas relacionadas
Otras colecciones temáticas
